• Home
• GR Corporate
• Products
• Markets
• Customer Support
• Distributor Locator
• What's New
• Events Calendar
• About Us
• Contact Us

Pocket Bellows Metering Pumps

Pocket Bellows Metering Pumps are the most economical metering pump on the market while maintaining the high quality standards of a Gorman-Rupp Industries product. PBMP line of bellows metering pumps are ideal for low flow, low pressure metering applications where a fixed flow rate is required.

Like the Mini Bellows Metering Pump line, the Pocket Bellows metering pumps are constructed entirely of plastic and uses GRI’s time-proven bellows technology to provide an accurate chemically-resistant metering pump with a long life, at an economical price. The only difference is the Pocket Bellows line utilizes a fixed crank mechanism.

Pocket Bellows Metering Pump Operation:
The Pocket Bellows Metering Pumps operate on a positive displacement principle. The rotation of the motor shaft is transmitted into an up and down linear motion through an adjustable concentric crank mechanism. This motion provides a continuous compressing and relaxing force on the bellows module, forcing fluid between two check valves located in the module’s valve body. Up to four separate bellows modules can be operated by single motor for proportioning up to four separate fluid mediums. The flow rate of each module is independently adjustable. Multiple bellows modules operate out-of-phase with each other for most efficient power usage.

Bellows Metering Pump Optimum Operating Conditions:
Optimum operating conditions consist of a 6” minimum suction life and a discharge head of not less than 6”. Pumps must be mounted vertically with the valve body at the top to obtain maximum metering accuracy. For conditions where a positive suction head condition exists, an anti-siphon spring or anti-siphon spring kit can be added to aid the poppet valve seal properly during operation. See Accessories PDF file located in the Product Resources section located above right.

Bellows Metering Pump Flow Rates:
The flow rate of each bellows module is regulated by three factors:

1. Diameter of the bellows,
2. Speed of the gearmotor,
3. Adjustment of the module stroke length.

The full stroke displacement and discharge pressure of the pump is dependent on the size of the bellows as shown below. If higher discharge pressure pressure is required, please consult factory for an OEM solution.

Pocket Bellows Metering Pump Specifications:
Flow Rates — Range from 2.7 ml/min to 240 ml/min
Max Discharge Pressures — Range to 6 psi.
Max Fluid Temperature — To 140°F (60°C)

Note: Reduce pressure rating by 50% for fluid temperatures over 120°F (49°C).

Viscosity/Slurries — Maximum fluid viscosity is 5,000 centistokes. Poppet valves can handle fine slurries. Duckbill valves are recommended for heavy slurries or fibrous materials. Heavy slurries should be flushed from the pump before shutdown.

Note: All testing is done with water at an ambient temperature of 80 degree F. If specific gravity or viscosity of fluid being pumped is significantly greater than water (1.0), please consult factory.

Materials in Contact with Solution:
Connectors — Polypropylene
O-Rings (Elastomers) — EPT/EPDM or Viton®/Fluoroelastomer
Poppet/Duckbill Valves — EPT/EPDM or Viton®/Fluoroelastomer
Bellows — Standard Polypropylene Materials
Additional materials available, refer to OEM Section for details.

Motors:
The standard motor available for the Pocket Bellows Metering Pump is an AC voltage synchronous motor. Motors are UL recognized and continuous duty rated and are available in 115V, 50/60 Hz or 230V, 50/60 Hz.

Pocket Bellows Metering Pump Selection:
The PBMP pump selection procedure is detailed in the Pump Selection Guide link under Product Resources above. Select a bellows size that meets your pressure requirements. Select a model with the bellows size that provides your required flow while operating closest to full stroke capacity. Best metering accuracy occurs when bellows modules operate at 50% or more of maximum output. For 24 hour continuous duty service, use one of the heavy-duty models.

Select a valve and O-ring combination and tubing connectors for each bellows from the selection charts at the end of this section. Specify duckbill valves if heavy slurries or fibrous materials are being pumped.
Refer to the Chemical Resistance Section to help determine compatibility.

Features
•	Average repeatability from stroke-to-stroke, ± 0.75%	•	Dry run capability
•	Self-priming	•	No dynamic seals
•	Superior corrosion resistance	•	Economical

OEM Options

Motors

Speeds Standard synchronous motor speeds are 8, 15 and 24 RPM at 60 Hz. Custom speeds available in shaded pole and DC motors, please consult factory. Voltages Standard voltages are 115V, 50/60 Hz or 230V, 50/60 Hz. However, the following special voltages are also available: 12 and 24VDC. Designs The standard motor is an AC voltage synchronous motor. Depending on the type of pocket bellows metering pump, the following motor types are available: shaded pole, and DC.

Poppet Valves and O-Rings

The standard elastomers for the poppet valves and O-rings are EPT/EPDM and Viton®/Fluoroelastomer. These elastomers have historically been able to handle the vast majority of the applications in which we’ve been involved. However, Butyl, Hydrin, Kel-F®, Silicone and Nitrile can be supplied for chemicals requiring such materials.

Duckbill Valves and O-Rings

Duckbill valves are required in those applications where heavy slurries or fibrous materials are being pumped. Heavy slurries should be flushed from the bellows before pump is shut down. Duckbill valves are available in the same elastomers as the poppet valves.